Getting started
OBD2 glossary: car diagnostic terms explained
What DTC, MIL, freeze frame, STFT, PID, closed loop, bank 1 and other acronyms that appear on the scan tool and in code pages mean.
Guide contents
In short
- A DTC names the circuit or function where a fault was detected, not the part.
- Pending, confirmed and permanent codes are three different stages of the same fault.
- Bank 1 is the side with cylinder 1; sensor 1 is before the catalytic converter.
- Positive fuel trim means the computer is adding fuel; negative means it is removing it.
Almost all diagnostic terms come from English, but they are rarely explained. This glossary covers the ones you will find on the scan tool, in manuals and in the code pages on this site, with a short explanation of each.
General concepts
- OBD2 (On-Board Diagnostics II)
- The vehicle self-diagnosis standard. It defines the connector, the communication protocols and the generic codes. Its European equivalent is called EOBD.
- DTC (Diagnostic Trouble Code)
- A five-character code, such as P0420, that identifies the circuit or function where a fault was detected.
- MIL (Malfunction Indicator Lamp)
- The check engine light. Steady means a confirmed fault; flashing means severe misfires.
- DLC (Data Link Connector)
- The 16-pin diagnostic connector, under the dashboard on the driver's side.
- Pending code
- A fault detected on one drive cycle that has not yet been confirmed on a second. It does not turn on the light.
- Confirmed or stored code
- A fault detected on consecutive drive cycles. It turns on the light if it affects emissions.
- Permanent code
- A code that cannot be cleared with a scan tool. It only disappears when the computer verifies that the fault does not return.
- Freeze frame
- A record of the engine data at the moment the code was confirmed. It is lost when codes are cleared.
- Readiness monitors
- Internal tests of the emissions systems. They must show ready to pass many emissions inspections.
- Drive cycle
- A driving sequence that lets the computer run its monitors: cold start, idle, city, highway and deceleration.
- PID (Parameter ID)
- The identifier for each piece of live data you can request from the computer: temperature, rpm, airflow and many more.
- OBD mode or service
- Each function of the protocol: 01 gives live data, 03 reads codes, 04 clears them, 07 shows pending codes and 0A permanent codes.
Modules and networks
- ECU, ECM and PCM
- The engine computer. The ECM controls only the engine; the PCM controls the engine and the transmission in one module.
- TCM
- Transmission control module.
- BCM
- Body control module: lights, locks, power windows and comfort features.
- CAN (Controller Area Network)
- The data network the modules use to talk to each other. Its faults set U codes.
- LIN
- A slower, simpler network for secondary components, such as switches or mirror motors.
Mixture and combustion
- Closed loop and open loop
- In closed loop the computer corrects the mixture using the oxygen sensor. In open loop, for example with a cold engine, it uses fixed values.
- STFT and LTFT
- Short and long-term fuel trims, as a percentage. Positive: adding fuel. Negative: removing fuel. See the fuel trim guide.
- Lean and rich mixture
- Lean: too much air or too little fuel. Rich: too little air or too much fuel.
- Lambda
- The ratio between the actual mixture and the ideal one. Lambda 1 is the stoichiometric mixture; above 1 is lean and below 1 is rich.
- Bank 1 and bank 2
- On V engines, each row of cylinders. Bank 1 is the one that contains cylinder number 1.
- Sensor 1 and sensor 2
- Oxygen sensor position: 1 before the catalytic converter, 2 after it.
- Misfire
- A cylinder that does not burn its mixture properly.
Most frequently mentioned sensors
- CKP and CMP
- Crankshaft and camshaft position sensors.
- MAF and MAP
- Mass of air entering the engine, and absolute pressure in the intake manifold.
- TPS and APP
- Throttle plate position and accelerator pedal position.
- ECT and IAT
- Engine coolant temperature and intake air temperature.
- O2, lambda sensor and A/F sensor
- Sensors that measure the oxygen in the exhaust gas. The A/F (wideband) sensor measures the mixture more precisely.
- KS
- Knock sensor: detects pinging so the computer can retard the timing.
- EVAP and EGR
- The fuel vapor control system and the exhaust gas recirculation system.
- Reference voltage
- The 5 V supply the computer sends to most sensors.