Getting started

How to read DTC codes with an OBD2 scan tool, step by step

Where the connector is, what to save before you clear anything, and how to interpret several codes at once without getting the priority wrong.

3 min read Updated November 14, 2026 Reviewed by Renzo Chacca

Guide contents

In short

  • The OBD2 port is within about 3 feet (1 m) of the steering wheel, almost always under the dash.
  • Save the freeze frame and every code before you clear anything.
  • If there are several codes, look for the common cause before repairing.
  • Clear codes only after the repair, and confirm it with a drive cycle.

Reading codes is the easy part of diagnosis. The hard part, and what separates fixing a fault from replacing parts blindly, is knowing what information to collect and in what order to interpret it. This guide follows the same procedure a professional shop uses.

1. Find the OBD2 port

Every vehicle with OBD2 has a 16-pin, trapezoid-shaped connector located within about three feet (one meter) of the steering wheel, almost always under the dashboard on the driver's side. On some models it is behind a cover, in the center console or inside the glove box. It must be reachable without tools: the standard requires it.

OBD2 J196212345678910111213141516
OBD2 connector (SAE J1962) seen from the front, as you see it under the dash. The colored pins are the ones defined by the standard.
PinFunction
16Battery positive (constant 12 V): powers the scan tool.
4 and 5Chassis ground and signal ground.
6 and 14CAN high and CAN low: used by almost every modern vehicle (mandatory in the US from the 2008 model year).
7 and 15K-line and L-line (ISO 9141-2 and KWP2000), common on older European and Asian vehicles.
2 and 10SAE J1850 bus (older Ford and GM).

2. Connect with the ignition on and the engine off

Turn the key to the on position without starting the engine. The scan tool is powered by the connector itself and needs the modules to be awake.

If the scan tool does not power up: check the cigarette lighter or diagnostic connector fuse before suspecting anything bigger. Without 12 V on pin 16, no reader will turn on.

3. Save the freeze frame before you touch anything

The freeze frame is the snapshot the computer took at the exact moment it confirmed the fault: RPM, engine load, coolant temperature, vehicle speed, fuel trims and manifold pressure. It is the most valuable information in the whole diagnosis, and it is lost as soon as you clear the codes. Write it down or take a photo of the screen.

4. Write down every code, not just the first one

When there are several codes there is almost always a hierarchy. A faulty crankshaft position sensor can trigger misfire codes on several cylinders; a loose ground can set codes on four different sensors. Before you repair anything, ask yourself which common cause could explain all the codes at once. The multi-code diagnosis helps you put them in order.

5. Tell active, pending and permanent codes apart

StatusWhat it meansWhat to do
Active (confirmed)The fault is present now and turned the light on.Diagnose and repair.
PendingIt was detected once and is waiting for confirmation on a second drive cycle.An early warning: check it before it confirms.
PermanentOnly the computer itself can erase it, after verifying that the fault does not return.Repair and drive until it clears; it fails an inspection even with the light off.

6. Look at live data before buying parts

With the engine running, the most informative parameters are the short and long-term fuel trims, the oxygen sensor signals, the mass airflow reading in grams per second and the coolant temperature. A value that never moves usually points to an open circuit or a sensor replaced by a default value. The live data guide lists the normal values.

7. Clear codes only after the repair

Clearing codes turns the light off but fixes nothing, and it also resets the readiness monitors. After the repair, clear the codes and complete a full drive cycle that mixes city and highway driving. Only when the monitors show ready again can you say the fault is fixed.

Keep reading

All diagnostic guides