P0824Generic code

P0824 Code: Gear Lever Y Position Circuit Intermittent

The P0824 code means the signal from the gear lever position sensor on the Y axis cuts out or jumps at times. The main effect is that the transmission does not recognize where the lever is. Intermittent faults almost always come from a loose connection or a damaged wire, so look there first.

Severity
High
Can I keep driving?
Yes, but with caution
Estimated cost
$60 to $800
Difficulty
Medium
System
Transmission
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P0824 code means

On transmissions with an electronic shifter (shift-by-wire) or automated ones, one or more sensors detect the position of the lever on the X and Y axes and send it to the transmission computer.

The sensor receives a 5 V reference and a ground from the computer and returns a signal of roughly 0.5 to 4.5 V. The intermittent dropouts behind the P0824 code are almost always caused by a loose connection or a damaged wire.

If the signal fails, the transmission does not know which gear the driver is asking for: it can stay in neutral or go into limp mode. On electronic shifters, the shifter module usually has the sensors built in.

Intermittent faults are found by reproducing them. With the engine running and the scan tool in graphing mode, move the wiring harness section by section, tap the connector gently and, if needed, warm the area with a hair dryer or wet the connector with a spray bottle. The spot where the reading jumps is where the fault is.

P0824 code symptoms

  • Check engine light on.
  • The transmission does not recognize the lever position.

Likely causes of the P0824 code

  1. Loose contact in the connector, with pins that are loose or pushed back.
  2. Wire broken inside its insulation, which opens the circuit with vibration.
  3. Harness rubbing against moving or hot parts.
  4. Sensor with an intermittent fault, often related to temperature.

How to diagnose the P0824 code step by step

  1. Read the sensor value on the scan tool and compare it with what is expected.
  2. Inspect the connector for corrosion, water or loose pins.
  3. Check power and ground with the key on: a correct reference and less than 0.1 V of drop on the ground.
  4. Measure the signal with the connector plugged in and see whether it changes with the condition.
  5. Do the wiggle test on the harness with the scan tool in graphing mode.
  6. Check the continuity of each wire up to the computer (under 1 ohm).

How to fix the P0824 code

  • Repair the connector or the wiring.
  • Replace the sensor if the tests confirm it.
  • Correct the real condition, if there is one.
  • Clear the codes and verify with a road test.

Technical reference data

  • 5 V reference, ground and a signal of 0.5 to 4.5 V.
  • These are approximate values: check the manufacturer data for your vehicle.

Brand-specific notes

The letter assignment and the location of the component change from one manufacturer to another, so check the manual for your vehicle.

Frequently asked questions about P0824

What does the P0824 code mean?
It is a generic OBD2 code that means the signal from the gear lever position sensor on the Y axis is cutting out or jumping intermittently. It is almost always a loose connection or a damaged wire.
Can I drive with a P0824 code?
Yes, with caution. With a P0824 code the transmission may stay in neutral or go into limp mode, so get it checked soon.
Does the sensor have to be replaced?
Only if the tests confirm it. The connector and the wiring fail just as often.
What does the gear lever position sensor do?
On transmissions with an electronic shifter (shift-by-wire) or automated ones, one or more sensors detect the position of the lever on the X and Y axes and send it to the transmission computer.
How much does it cost to fix P0824?
As a rough guide, between $60 and $800.
Will a P0824 code clear itself?
The light can go out while the connection behaves, but an intermittent fault usually returns. Finding the loose pin or damaged wire is the only way to fix it for good.
What is the most common cause of P0824?
A loose contact in the connector or a wire broken inside its insulation. Vibration and heat make the circuit open and close.

Related codes

Questions about the P0824 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.