P2306Generic code

P2306 Code: Ignition Coil C Primary Control Circuit Low

The P2306 code means the computer sees low voltage in the control circuit of ignition coil C, either a short to ground or a missing supply. It can cause misfires on one or two cylinders, jerking and loss of power. You can drive short distances with caution, but a cylinder with no spark can damage the catalytic converter.

Severity
High
Can I keep driving?
Yes, but with caution
Estimated cost
$30 to $200
Difficulty
Medium
System
Ignition and Misfires
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P2306 code means

On engines with one coil per cylinder (coil on plug) or with dual coils, the computer controls the primary circuit of each coil: it charges the coil for a few milliseconds and then cuts the current so the spark jumps. The letters A, B, C and so on identify each coil or each control circuit depending on the manufacturer. On many engines A corresponds to cylinder 1.

The computer monitors the control circuit from its own driver transistor. The P2306 code means low voltage in the control circuit (a short to ground or a missing supply) on coil C. Before you replace the component, check the fuse, relay, connector and wiring, because they are the most common cause.

Many modern coils have the ignition transistor built in and receive a low voltage trigger signal from the computer. A short to ground or an open circuit in that signal leaves the coil with no spark.

To confirm it, unplug the component with the key on and watch what happens to the reading or the code. If the value jumps to the opposite extreme, the wiring is fine and the component is the one pulling the signal to ground. If nothing changes, look for the short in the wire, starting where the harness rubs against the engine, the chassis or the exhaust.

P2306 code symptoms

  • Check engine light or another warning light on.
  • Misfires on one or two cylinders, jerking and loss of power.

Likely causes of the P2306 code

  1. Control wire shorted to ground. The component can stay on all the time, or the computer cuts the command to protect itself.
  2. Interrupted supply. A blown fuse, a faulty relay or a cut wire.
  3. Shorted component. Resistance far below the specification.
  4. Connector with moisture that creates a path to ground.

How to diagnose the P2306 code step by step

  1. Activate the component with the scan tool and check whether it responds.
  2. Check the fuse and relay. Measure the voltage on both sides of the fuse, and swap the relay with an identical one.
  3. Measure the supply at the connector. Battery voltage with the key on or when it is activated.
  4. Measure the resistance of the component and compare it with the manual. Check the insulation to ground too.
  5. Check the control wire. Continuity to the computer and no shorts.

How to fix the P2306 code

  • Repair the connector, the wiring or the supply.
  • Replace ignition coil C if it does not respond with correct power and command.
  • Clear the codes and verify.

After the repair, check the spark plug of the same cylinder and make sure the P2306 code stays away and there are no misfires on the scan tool.

Technical reference data

  • Coil with a built-in igniter: 12 V supply, ground and a trigger signal of 0 to 5 V.
  • Primary resistance of coils without a built-in igniter: 0.4 to 2 ohms.
  • Always check the spark plug of the same cylinder too.
  • These are reference values only: check the manufacturer data for your vehicle.

Brand-specific notes

This code is very common on several makes. Swapping the coil with the one from another cylinder is the quickest test: if the misfire follows the coil, the coil is bad.

P2306 on Volkswagen

Very frequent on Volkswagen 1.8T and 2.0 TFSI engines.

P2306 on Audi

Very frequent on Audi 1.8T and 2.0 TFSI engines.

P2306 on SEAT

Very frequent on SEAT 1.8T and 2.0 TFSI engines.

P2306 on Ford

Very frequent on Ford vehicles.

P2306 on Chevrolet

Very frequent on Chevrolet vehicles.

P2306 on Hyundai

Very frequent on Hyundai vehicles.

P2306 on Kia

Very frequent on Kia vehicles.

Frequently asked questions about P2306

Can I drive with a P2306 code?
Only short distances and without pushing the engine. A cylinder with no spark sends fuel to the catalytic converter and can damage it. If the light is flashing, stop driving.
What does ignition coil C do?
On engines with one coil per cylinder (coil on plug) or with dual coils, the computer controls the primary circuit of each coil. It charges the coil for a few milliseconds and then cuts the current so the spark jumps. The letter C identifies one of those coils or control circuits.
Does the part always have to be replaced?
No. Check the fuses, relays, connectors and wiring first.
How much does it cost to fix P2306?
Roughly $30 to $200. A connector or wiring repair is at the low end, and a coil with labor is closer to the top.
What does the P2306 code mean?
It is a generic OBD2 code that means the primary control circuit of ignition coil C has low voltage. The cause is a short to ground or a missing supply.
Will a P2306 code clear itself?
If the cause was moisture in the connector, the light may go out once it dries. A shorted coil or a damaged wire will bring the code back, so find the cause.
What is the most common cause of P2306?
A fault in the fuse, relay, connector or wiring is the most common, ahead of the coil itself. A shorted coil is the next most likely.

Related codes

Questions about the P2306 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.