P2182Generic code

P2182 Code: Engine Coolant Temperature Sensor 2 Circuit

The P2182 code means the computer found an electrical fault in the circuit of coolant temperature sensor 2. The main effect is that the cooling fan may run all the time and temperature control becomes less precise. You can drive with caution while you watch the temperature gauge.

Severity
Medium
Can I keep driving?
Yes, but with caution
Estimated cost
$20 to $150
Difficulty
Medium
System
Idle and Speed Control
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P2182 code means

Some engines have two coolant temperature sensors: one at the engine outlet and another at the radiator or somewhere else in the cooling circuit. With both, the computer controls the cooling fan and the electronic thermostat, and it can detect cooling system faults.

The sensor changes its resistance with temperature, and the computer measures the resulting voltage. A circuit fault can come from the sensor, the wiring or the power supply.

It is an NTC thermistor, which means its resistance drops as the temperature rises. A sensor guide shows how to test one.

Always start with the simplest things: fuse, relay and connector. Then check power, ground and signal with the component plugged in (using back-probes), and last the continuity of each wire to the computer. Only if all of that checks out should you replace the component.

P2182 code symptoms

  • Check engine light on.
  • The cooling fan may run all the time, and temperature control becomes less precise.

Likely causes of the P2182 code

  1. Damaged or corroded connector. The most common cause.
  2. Cut or shorted wiring between the sensor and the computer.
  3. Failed sensor. Open or internally shorted.
  4. Missing power reference. Check whether other sensors are also failing.
  5. Computer. Uncommon, so rule out everything above first.

How to diagnose the P2182 code step by step

  1. Read the sensor value on the scan tool and compare it with what you expect.
  2. Inspect the connector for corrosion, water or loose pins.
  3. Check power and ground with the key on: correct reference voltage and less than 0.1 V drop on the ground.
  4. Measure the signal with the connector plugged in and see whether it changes with the conditions.
  5. Do a wiggle test on the wiring with the scan tool in graph mode.
  6. Check the continuity of each wire to the computer (less than 1 ohm).

How to fix the P2182 code

  • Repair the connector or the wiring.
  • Replace the sensor if the tests confirm it is bad.
  • Correct the real condition if there is one.
  • Clear the codes and verify with a road test.

Clear the P2182 code and keep an eye on the temperature gauge during the road test. If it climbs above normal, stop the vehicle and let the engine cool down.

Technical reference data

  • Approximate resistance: 2 to 3 kilohms at 68 °F (20 °C) and 200 to 300 ohms at 194 °F (90 °C).
  • Signal: about 3 to 4 V cold and 0.5 to 1 V hot.
  • These are reference values only: check the manufacturer data for your vehicle.

Brand-specific notes

The P2182 code is common on engines with an electronic thermostat and on engines with a sensor mounted in the radiator.

P2182 on BMW

Frequent on BMW engines with an electronic thermostat.

P2182 on Volkswagen

Frequent on Volkswagen engines with an electronic thermostat.

P2182 on Ford

Seen on several Ford engines that have the sensor in the radiator.

P2182 on GM

Seen on several GM engines that have the sensor in the radiator.

Frequently asked questions about P2182

Can I drive with a P2182 code?
Yes, while watching the temperature gauge. If it climbs above normal, pull over and stop.
Does the sensor have to be replaced?
Only if the tests confirm it. The connector and the wiring fail just as often as the sensor.
What does coolant temperature sensor 2 do?
Some engines have two coolant temperature sensors: one at the engine outlet and another at the radiator or elsewhere in the circuit. With both, the computer controls the fan and the electronic thermostat and can spot cooling system faults.
How much does it cost to fix P2182?
Roughly $20 to $150. A connector or wiring repair sits at the low end, and a new sensor with labor is closer to the top.
What does the P2182 code mean?
It is a generic OBD2 code for an electrical fault in the circuit of engine coolant temperature sensor 2. The fault can be in the sensor, the wiring or the power supply.
Will a P2182 code clear itself?
If the fault was a momentary glitch, the light can go out after several drive cycles. A damaged connector or wire will bring it back, so find the cause.
What is the most common cause of P2182?
A damaged or corroded connector. Check it before you spend money on a new sensor.

Related codes

Questions about the P2182 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.