P0812Generic code

P0812 Code: Reverse Input Circuit

The P0812 code means there is an electrical fault in the reverse gear input circuit. The main effect is backup lights or a camera that do not work. It is a minor problem that is cheap to fix and safe to drive with.

Severity
Low
Can I keep driving?
Yes, no immediate risk
Estimated cost
$20 to $250
Difficulty
Medium
System
Transmission
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P0812 code means

A switch tells the computer that reverse gear has been engaged, so it can turn on the backup lights and notify other systems (the camera and the sensors).

It is a switch: the computer sees a high or low voltage depending on its position. A circuit fault, the P0812 code, can come from the switch, the wiring or the power supply.

If the signal fails, the backup lights or the camera may not work.

Always start with the simplest items: fuse, relay and connector. Then check power, ground and signal with the component connected (using back-probes), and finally the continuity of each wire up to the computer. Only if all of that is good should you replace the component.

P0812 code symptoms

  • Check engine light on.
  • Backup lights or camera that do not work.

Likely causes of the P0812 code

  1. Damaged or corroded connector. The most frequent cause.
  2. Wiring cut or shorted between the switch and the computer.
  3. Failed switch, open or shorted internally.
  4. Missing power reference. Check whether other sensors are also failing.
  5. Computer. Uncommon; rule out everything above first.

How to diagnose the P0812 code step by step

  1. Read the switch value on the scan tool and compare it with what is expected.
  2. Inspect the connector for corrosion, water or loose pins.
  3. Check power and ground with the key on: a correct reference and less than 0.1 V of drop on the ground.
  4. Measure the signal with the connector plugged in and see whether it changes with the condition.
  5. Do the wiggle test on the harness with the scan tool in graphing mode.
  6. Check the continuity of each wire up to the computer (under 1 ohm).

How to fix the P0812 code

  • Repair the connector or the wiring.
  • Replace the switch if the tests confirm it.
  • Correct the real condition, if there is one.
  • Clear the codes and verify with a road test.

Technical reference data

  • The switch or sensor is powered from the computer: check the manual for the values.
  • These are approximate values: check the manufacturer data for your vehicle.

Brand-specific notes

The letter assignment and the location of the component change from one manufacturer to another, so check the manual for your vehicle.

Frequently asked questions about P0812

What does the P0812 code mean?
It is a generic OBD2 code that means there is an electrical fault in the reverse gear input circuit. The cause can be the switch, its wiring or its power supply.
Can I drive with a P0812 code?
Yes, with caution. The backup lights or the camera may not work, so take extra care when you back up.
Does the switch have to be replaced?
Only if the tests confirm it. The connector and the wiring fail just as often.
What does the reverse input do?
A switch tells the computer that reverse gear has been engaged, so it can turn on the backup lights and notify other systems such as the camera and the sensors.
How much does it cost to fix P0812?
As a rough guide, between $20 and $250.
Will a P0812 code clear itself?
It can go out if the connection was only loose or damp for a moment. A damaged connector, wire or switch will bring the P0812 code back.
What is the most common cause of P0812?
A damaged or corroded connector. Check it and the wiring before you buy a switch.

Related codes

Questions about the P0812 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.