P0185Generic code

P0185 Code: Fuel Temperature Sensor B Circuit

The P0185 code means the computer found an electrical fault in the fuel temperature sensor B circuit: it is getting an impossible signal or no signal at all. The most common causes are a damaged connector, a broken wire or the sensor itself. Confirm which sensor is B on your engine before you test anything.

Severity
Low
Can I keep driving?
Yes, no immediate risk
Estimated cost
$40 to $300
Difficulty
Medium
System
Fuel Injection
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P0185 code means

Fuel temperature sensor B is the second measuring point in the fuel system (depending on the manufacturer, another section of the rail, the return line or the second tank). The computer uses it because it complements the sensor A reading, which lets it correct injection and protect the system.

The computer constantly checks that the fuel temperature sensor B signal stays within the possible electrical limits. The P0185 code means it detected a fault in the circuit: the signal disappeared, went out of range or does not match any physically possible value. This is a generic code that some manufacturers use instead of the specific low or high signal codes.

Keep in mind that the code points to the circuit where the computer saw the problem, not necessarily the part that failed. Check the wiring before you replace the sensor, and treat the P0185 code as a starting point for testing rather than a parts list.

P0185 code symptoms

  • Check engine light on and steady.
  • In many cases you notice nothing while driving, only the light on the dash.
  • Possible companion codes from the same sensor (low, high or intermittent signal).

Likely causes of the P0185 code

  1. Damaged, loose or corroded connector. This is the most common cause.
  2. Cut or shorted wiring between the sensor and the computer.
  3. Failed sensor, open or shorted inside.
  4. Missing supply reference, 5 V or 12 V depending on the sensor design.
  5. Computer failure. This is very rare, so rule out everything else first.
  6. Also check: Look in the service manual to see which sensor is B on your engine, because the assignment changes between manufacturers.

How to diagnose the P0185 code step by step

  1. Read the live data from the sensor and compare it with what you expect. After the vehicle has sat for several hours, it should match sensor A and the ambient temperature.
  2. Inspect the connector. Unplug it, look for green, backed-out or oily pins, and plug it back in firmly.
  3. With the key on and the sensor unplugged, measure the reference at the connector. You should see about 5 V between the signal pin and ground.
  4. Do the jumper test. With the sensor unplugged, the scan tool should show about -40 °C (-40 °F). When you join the two connector pins with a jumper wire, the reading should jump to over 120 °C (248 °F). If it does, the wiring is good and the problem is the sensor.
  5. Measure the sensor resistance and compare it with the technical data table at the current temperature.
  6. Do a wiggle test. With the engine running, move the harness and the connector while you watch the live data. A sudden jump gives away the spot where the fault is.
  7. Check the continuity of each wire between the sensor connector and the computer connector with the key off.

How to fix the P0185 code

  • Repair the damaged connector or wiring.
  • If the supply, ground and wiring all test good, replace the sensor.
  • Clear the codes and confirm they do not come back.
  • Use a quality OE or equivalent sensor. Cheap generic ones often have different response curves.
  • Clear the codes, drive a full drive cycle and check in the live data that the reading makes sense.

Technical reference data

  • Two-wire NTC thermistor with a 5 V reference.
  • Approximate resistance: 2,000 to 3,000 ohms at 20 °C (68 °F).
  • Open circuit: about -40 °C (-40 °F). Short circuit: over 120 °C (248 °F).
  • These are approximate values. Check the manufacturer data for your engine.

Brand-specific notes

This is an uncommon code. It shows up mostly on diesels and on vehicles with two fuel tanks.

If you cannot find sensor B on your engine, check the manufacturer information before you buy any parts.

Frequently asked questions about P0185

What does the P0185 code mean?
The P0185 code means the computer detected an electrical fault in the fuel temperature sensor B circuit: the signal disappeared, went out of range or does not match any value that is physically possible. It is a generic circuit code that some manufacturers use instead of the specific low or high signal codes. The fault is in the circuit, which is not always the sensor itself.
Can I drive with a P0185 code?
Yes, in general there is no immediate risk. The engine runs on a substitute value and may use a bit more fuel, so get it repaired soon.
What is the most common cause of P0185?
The most common cause is a damaged, loose or corroded connector. Cut or shorted wiring between the sensor and the computer is next, and then the sensor itself.
Does the P0185 code always mean I need a new fuel temperature sensor B?
No. In most cases the fault is in the connector or the wiring. Do the supply, ground and continuity tests first, and replace the sensor only when those pass.
What is the difference between a low signal and a high signal?
On a thermistor, a low signal means an impossibly high temperature (a short), and a high signal means an impossibly low temperature (an open circuit).
How much does it cost to fix P0185?
Roughly $40 to $300. The cheap end is repairing a connector, and the expensive end is replacing the sensor with labor. Prices vary by region and shop.
Will a P0185 code clear itself?
Not on its own. If the cause was a loose connector that you have fixed, the code will not come back, but if the fault is still there the computer sets P0185 again. Clearing it with a scan tool without finding the cause only hides it for a while.

Related codes

Questions about the P0185 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.